橡膠接頭漏水的最大的原因應該是由于安裝不準確。近一些客戶反應橡膠接頭產品在安裝和試運行會有漏水現象，出廠前都是通過壓力測試和嚴密封閉性實驗測試，符合標準后才會銷售到客戶手中。上海松夏減震器有限公司的技術擔擔任職務務的人覺得安裝運用有誤，可曲撓橡膠接頭在法蘭聯接過程中利用可曲撓橡膠接頭自身橡膠端面的突出橡膠邊緣作為嚴密封閉材料來嚴密封閉橡膠軟接頭法蘭端面，所以一樣在扣槽橡膠軟接頭容易發生漏水現象，端面全嚴密封閉橡膠軟接頭不會有這種現象，主要原因是扣槽橡膠接頭安裝時刻沒有很好的將橡膠嚴密封閉端面很好的卡進法蘭的凹槽中，這樣橡可曲撓橡膠接頭在運用過程中容易發生部分壓力集中在邊緣處顯露出來泄露。在可曲撓橡膠接頭安裝過程中必須使橡膠邊沿卡扣到到法蘭槽里，所以安裝后反法蘭可以很嚴密封閉的卡住橡膠端好，運用中不會出現滲漏現象。當有部分的安裝工作，螺釘不泄露，這是不準確的嚴密封閉面泄露后，擰緊螺釘將粉碎橡膠邊緣，使嚴密封閉面損傷，橡膠球的表面的一小批遭到破壞。這種方法是不準確的，我廠泄露，該橡膠軟接頭卸下被還原，之后調整裝置。
The biggest cause of rubber joint leakage should be due to inaccurate installation.Recently, some customers reported that there would be water leakage in the installation and trial operation of rubber joint products. Before leaving the factory, they all passed the pressure test and tight sealing test, and were sold to customers after meeting the standards.Pine xia shock absorber co., LTD. Shanghai technical bear positions of people think that using the wrong installation, in a flexible rubber joint used in the process of flange connection in a flexible rubber joint of rubber face own outstanding rubber edge to tightly closed as tightly closed material rubber soft joint flange end face, so the same accounting groove soft rubber joints are prone to leakage phenomenon, face all tightly closed soft rubber joints will not have this kind of phenomenon, the main reason is that buckle slot will be a very good rubber joint installation moments don't have rubber tightly closed end face good card into the groove of the flange,This flexible rubber joints in the use of the process is prone to part of the pressure concentrated on the edge of the exposed leak.In the installation process of flexible rubber joint, it is necessary to make the rubber edge buckle into the flange slot, so the anti-flange can be very close to the stuck rubber end after installation, there will be no leakage in use.When there is part of the installation work, the screw does not leak, which is inaccurate tight sealing surface leakage, tighten the screw will crush the rubber edge, so that the tight sealing surface damage, rubber ball surface of a small batch of damage.This method is not accurate, I plant leakage, the rubber soft joint was removed after the reduction of the adjustment device.
The biggest cause of rubber joint leakage should be due to inaccurate installation.Recently, some customers reported that there would be water leakage in the installation and trial operation of rubber joint products. Before leaving the factory, they all passed the pressure test and tight sealing test, and were sold to customers after meeting the standards.Pine xia shock absorber co., LTD. Shanghai technical bear positions of people think that using the wrong installation, in a flexible rubber joint used in the process of flange connection in a flexible rubber joint of rubber face own outstanding rubber edge to tightly closed as tightly closed material rubber soft joint flange end face, so the same accounting groove soft rubber joints are prone to leakage phenomenon, face all tightly closed soft rubber joints will not have this kind of phenomenon, the main reason is that buckle slot will be a very good rubber joint installation moments don't have rubber tightly closed end face good card into the groove of the flange,This flexible rubber joints in the use of the process is prone to part of the pressure concentrated on the edge of the exposed leak.In the installation process of flexible rubber joint, it is necessary to make the rubber edge buckle into the flange slot, so the anti-flange can be very close to the stuck rubber end after installation, there will be no leakage in use.When there is part of the installation work, the screw does not leak, which is inaccurate tight sealing surface leakage, tighten the screw will crush the rubber edge, so that the tight sealing surface damage, rubber ball surface of a small batch of damage.This method is not accurate, I plant leakage, the rubber soft joint was removed after the reduction of the adjustment device.
微信二維碼